Nozzle Orientation Marking Calculator

Terms Used in Nozzle Orientation Marking Calculator Calculator

Outer Circumference (OCF)

Outer Circumference is measure along shell outer diamter. It is denoed by (OCF). This dimension is used for calculating nozzle marking distance along shell. It is required while calculating shell nozzle orientation marking distance. You can use any dimentional units such as Inches or MM as per your prefererance. if you are using Inches as units for your input values then please refer decimal fractional chart to enter proper input values.

Nozzle Angle (α)

Nozzle Angle (α) is the nozzle orientation angle measured from its zero degree angle or from its quadrant. It is denoted by α in this Calculator. You can refere standarad input image shown in this calculator for you better understanding.You can use any dimentional units such as Inches or MM as per your prefererance. if you are using Inches as units for your input values then please refer decimal fractional chart to enter proper input values.

Dish End Diameter (D)

Dish End Diameter is outside diameter of dish end. It is denoted by D in this Calculator. you have to provide input as outside diamter because we are going t mark nozzle on out side of the dish ends. if you are marking nozzle inside of the dish end then only you can use inside diameter but in actual practice we are always mark nozzle from outer side so it is recmmended to use outer diameter. You can refere standarad input image shown in this calculator for you better understanding.You can use any dimentional units such as Inches or MM as per your prefererance. if you are using Inches as units for your input values then please refer decimal fractional chart to enter proper input values.

Nozzle Distance (C)

Nozzle Center Distance is distance of nozzle center from its dish end center. It is denoted by C in this Calculator. You can refere standarad input image shown in this calculator for you better understanding. if you are using Inches as units for your input values then please refer decimal fractional chart to enter proper input values.

Shell Outside Diameter(OD)

Shell outside diameter is calculated by this calculator it is calculated based on your outer crcumference input values.

Crown Radius (C.R)

dish end crown radius is the radius of the crown section. it is calculated by our calculator based on your dish end type selection.

Nozzle Arc Distance (A)

Nozzle Arc Distance is the nozzle marking distance calculated by this calculator for marking dish end nozzle. it is arc deistance measure from the ceneter point of the dish ends.

What are Types of Dish End option available in this Nozzle Orientation Marking Calculator

In this Nozzle Orientation Marking Calculator, we have the following Types of Dish End Options are available.

1. 10% Torispherical Dish Ends
2. 2:1 Eliptical Dish Ends
3. Hemispherical Dish Ends

What are Types of Nozzle Orientation Options Available with Nozzle Orientation Marking Calculator

In this Nozzle Orientation Marking Calculator, we have the following Types of Nozzle Orientation Options are available.

1. Shell Nozzle Orientation Marking Calculator
2. Dish End Nozzle Orientation Marking Calculator

How to Use this Nozzle Orientation Marking Calculator

1. Firstly Navigate to the Nozzle Orientation Marking Calculator and Select the Type of Nozzle option from Selection pannel.
2. After Nozzle Types Selection you have to refere standard input image of this types of nozzle type and make list of dimensions required in this calculator and keep handy this dimentions.
3. Select Input Dimensions Stanarad Units from Unit selection pannel. if you are using inches as dimenions then please refer to note below input selection to refere decimal factor selection chart.
4. Input all the dimension required in given input fields as per your unit selection. All dimensions are required to fill before moving ahead.
5. after completing all input field data click on calculate button to generate output of result of your selected nozzle orientation types.
6. If you left any input field empty then it will show you an error notification so if you are getting this notification then check all your empty fields and enter correct data to generate results.
7. Navigate below to calculate button to see generated output result dimensions.
8. Refere Outpt Image to understand out marking dimensions vales to mark accurately.
9. By using this Data you can mark you nozzle directly on your shell and dish ends.

if you want to learn the fabrication layout marking method of Pipe Branch Connections then click here to download our ebook “Master in Fabrication Layout Development”. In this book all both Geometrical and Numerical Method of fabrication Layout of all types of the branch pipe connections.

Why Should Use this Nozzle Orientation Marking Calculator

1. Nozzle Orientation Marking Calculator is useful for calculating marking distance of nozzle on shell and dish ends.
2. Nozzle Orientation Marking Calculator provide complete solution to Nozzle Markings.
3. You Can save the Cost of Material by using this calculator.
4. You can Save Time on your Nozzle Marking process.
5. An easy and Faster way to mark nozzle on shell and dish ends.

Application Area of Nozzle Orientation Marking Calculator

Nozzle Orientation Marking Calculator is useful for Pressure Vessel Fabrication Industry,Process Equipment Fabrication Industry, Piping Industry, Storage Tank Fabrication Industry, Heat Exchanger Fabrication Industry, Heavy Equipment Fabrication Industry or any similar Industry

Click here to Download App for Android Device.

Click here to Download App for Apple Device.

If you are looking for Various other useful fabrication Apps for your daily fabrication activity then Click here

If you want to increase your knowledge by learning from us then you can join our various video courses in the field of fabrication Click here to know more about our courses